Tektronix DPO7254

DPO7254
Features and Benefits: 3.5 GHz Bandwidth Model for Serial and Digital Applications Up to... mehr
Produktinformationen "Tektronix DPO7254"
Features and Benefits: 3.5 GHz Bandwidth Model for Serial and Digital Applications Up to 40 GS/s Real-time Sample Rate on One Channel and up to 10 GS/s on All Four Channels Up to 500 Megasamples Record Length with MultiView Zoom™ Feature for Quick Navigation >250,000 wfms/s Maximum Waveform Capture Rate Up to 310,000 Waveforms per Second with FastFrame™ Segmented Memory Acquisition Mode User-selectable Bandwidth Limit Filters for Better Low-frequency Measurement Accuracy MyScope® Custom Windows and Right Mouse Click Menus for Exceptional Efficiency Event Search and Mark to Find Specific Events in the Entire Waveform Pinpoint® Triggering provides the Most Flexible and Highest Performance Triggering, with Over 1400 Combinations to Address Virtually Any Triggering Situation. 12.1” XGA Display with Touch Screen Communications Mask Testing Clock Recovery from Serial Data Streams 64-bit NRZ Serial Pattern Trigger for Isolation of Pattern-dependent Effects up to 1.25 Gb/s Low-speed Serial Protocol Triggering and Decode (I2C, SPI, RS-232, CAN, LIN, and FlexRay) Technology-specific Software Solutions provide Built-in Domain Expertise for MIPI® D-PHY, Ethernet, USB 2.0 Compliance Testing, Jitter, Timing, Eye Diagram, Power, DDR Memory Bus Analysis, CAN, LIN, and FlexRay Network Design OpenChoice® Software with Microsoft Windows XP OS enables Built-in Networking and Extended Analysis Applications: Signal Integrity, Jitter, and Timing Analysis Verification, Debug, and Characterization of Sophisticated Designs Debugging and Compliance Testing of Serial Data Streams for Telecom and Datacom Industry Standards Low-speed Serial Bus Design (I2C, SPI, RS-232, CAN, LIN, and FlexRay) Investigation of Transient Phenomena Power Measurements and Analysis Spectral Analysis Characteristics: Vertical System: Input Channels: 4 Bandwidth (DSP Bandwidth Enhance): 3.5 GHz Rise Time (DSP Bandwidth Enhance): 115 ps Hardware Analog Bandwidth (-3 dB): 2.5 GHz Rise Time 10% to 90% (Typical): 145 ps Rise Time 20% to 80% (Typical): 95 ps DC Gain Accuracy: ±1% with offset/position set to 0 Input Coupling: AC, DC, GND Input Impedance (Software selectable): 1 MO ±1% with 13 pF ±2 pF or 50 O ±1% Input Sensitivity: 1 MO: 1 mV/div to 10 V/div 50 O: 1 mV/div to 1 V/div Vertical Resolution: 8 bit (>11 bit with Hi Res) Max Input Voltage: 1 MO: ±150 V CAT I, derate at 20 dB/decade to 9 VRMS above 200 kHz 50 O: 5 VRMS with peaks less than ±24 V Position Range: ±5 divisions Offset Range: 1 mV/div to 50 mV/div: ±1 V 50.5 mV/div to 99.5 mV/div: ±(1.5 V – 10 divisions) 100 mV/div to 500 mV/div: ±10 V 505 mV/div to 995 mV/div: ±(15 V – 10 divisions) 1 V/div to 5 V/div: ±100 5.05 V/div to 10 V/div: ±(150 V – 10 divisions) Offset Accuracy: 1 mV/div to 9.95 mV/div: ±0.2% (offset value-position) ±0.1 div ±1.5 mV 10 mV/div to 99.5 mV/div: ±0.35% (offset value-position) ±0.1 div ±1.5 mV 100 mV/div to 1 V/div: ±0.35% (offset value-position) ±0.1 div ±15 mV 1.01 V/div to 10 V/div: ±0.25% (offset value-position) ±0.1 div ±150 mV Delay Between Any Two Channels (Typical): =100 ps (50 O, DC coupling and equal V/div at or above 10 mV/div) Channel-to-Channel Isolation (Any 2 channels at equal Vertical Scale Settings) (Typical): =100:1 at =100 MHz =30:1 between 100 MHz and 2.5 GHz > 20:1 between 2.5 and 3.5 GHz Time Base System: Time Base Range: 25 ps/div to 1000 s/div Time Resolution (in ET/IT mode): 250 fs Time Base Delay Time Range: 5 ns to 250 s Channel-to-Channel Deskew: Range ±75 ns Delta Time Measurement Accuracy: ((0.06 / sample rate) + (2.5 ppm × Reading)) RMS Trigger Jitter (RMS): 1.5 psRMS (typical) with enhanced triggering OFF Jitter Noise Floor: Time Base Accuracy: ±2.5 ppm + Aging Acquisition System: Real-Time Sample Rates: 1 Channel (Max): 40 GS/s 2 Channels (Max): 20 GS/s 3-4 Channels (Max): 10 GS/s Equivalent Time Sample Rate (Max): 4 TS/s (for repetitive signals) Maximum Record Length Per Channel: Standard Configuration: 1 Channel: 50 M 2 Channel: 25 M 4 Channel: 12.5 M Record Length Opt. 2RL: 1 Channel: 125 M 2 Channel: 50 M 4 Channel: 25 M Record Length Opt. 5RL 1 Channel: 250 M 2 Channel: 125 M 4 Channel: 50 M Record Length Opt. 10RL 1 Channel: 500 M 2 Channel: 250 M 4 Channel: 125 M Maximum Duration at Highest Real-Time Resolution (1 Channel): Resolution: 25 ps (40 GS/s) Max Duration with Standard Record Length and Sample Rate: 1 ms Max Duration with Opt 2RL: 2 ms Max Duration with Opt 5RL: 5 ms Max Duration with Opt 10RL: 10 ms
Produktgruppe Oszilloskope / Analog-
  • 7E373738-E0C7-4E27-828E-87DC44740E3C
 
Verfügbar in folgenden Varianten:
10RL
Preis auf Anfrage
5RL
Preis auf Anfrage

inkl. MwSt. zzgl. Versandkosten

Weiterführende Links zu "DPO7254"

Beratungs-Hotline

Unser Team steht Ihnen fachkundig zur Seite.+49 6151 / 39980